The New & Improved Optimum Gelcoat Restorer is engineered to return Gelcoat to its original factory finish without the need for polishing. The new formula is easier to apply and levels itself better for faster application times and a more even application. Optimum Gelcoat Restorer ("GCR") rebuilds the Gelcoat keeping the original thickness and restoring the gloss as before while adding additional UV protection to protect from oxidation. Directions: 1. Remove loose oxidation using pure Optimum Power Clean and a brush or mild scuff pad. 2. Rinse the surface thoroughly and dry. 3. Wearing gloves and eye protection, apply GCR to the surface in overlapping circular motions. If the Gelcoat was heavily oxidized, the GCR will soak in. Do not over apply, first coats should be very thin. Use a pearl weave, low nap towel for application. 4. Once dry to the touch (20-30 minutes), apply a second coat. Apply directly onto towel, not on panel. A sprayer can be attached to GCR bottle or product transferred for application. When the applicator begins to drag, add more product. 5. Depending on the level of oxidation, up to 5 coats may be required. Last pass, apply in straight lines. 6. To maintain the restored surface, wash with Optimum No Rinse (ONR) and apply Optimum Car Wax regularly. 7. One bottle of GCR is enough for 4 coats on a 40’ Boat or RV. Gelcoat Hints: • Thin coats and multiple coats (up to 5) • Only use on old/fading gelcoat • Can be applied in bright sunlight. • Sticky/spotty if too much applied • Use DAMP pearl weave towels, low nap, for smoother application. • 2-3 year durability (wax every 6 months) – Absorbs into the gel coat and restores from the inside out. • It’s acrylic based. • To remove streaking, polish with Hyper Polish and orange foam pad (or if necessary, move up to Intensive Polish). There are four major points for best application for GCR: 1. The condition of the Gelcoat – Will GCR work on it or not? Gelcoat Restorer is made for heavily oxidized paint. New Gelcoat isn’t porous as old, oxidized Gelcoat so it won’t accept the product, whether it is clear or colored Gelcoat. 2. Removing this oxidized Gelcoat is essential for the pores to accept the coating, exactly like prepping paint for coating, with concentrated Power Clean and white scuff pad. 3. The amount of product also essential, multiple moderate layers are better than one thick coat, both will streak. After removing the oxidized layer, the Gelcoat will look clean but dull. After 1-3 layers there may not be much gloss. Layers 4-5, the gloss will improve. 4. What you apply with is as important as the amount, a DAMP pearl weave towel or low nap MF applicator is the best way to apply GCR.

Optimum Opti-Lens Coating is the most advanced polymer system that is specifically designed for the protection of headlight lenses. This hybrid resin is a combination of Opti-Coat 2.0 ceramic resin and an acrylic resin for maximum bonding and protection of acrylic and polycarbonate lenses. Additionally Optimum Opti-Lens Coating contains high levels of UV absorbers to minimize discoloration and fading of automotive headlight lenses. Optimum Opti-Lens Coating is highly concentrated and one tube is enough to cover 5-6 sets of headlights. Once applied, Optimum Opti-Lens Coating will form a permanent bond to the surface and can only be removed by polishing or paint removers. Directions: 1. Clean headlights with 15% IPA solution to remove any oils, waxes, or sealants. 2. Remove all the oxidation by sanding and then polishing the headlights with Optimum Polish II or Optimum Hyper Polish. 3. Wipe down the entire lens with a clean damp microfiber towel to remove any polishing residue. 4. Prime the applicator pad by making an X pattern across the pad. Only a few drops will be needed per headlight lens. 5. Wipe Optimum Opti-Lens Coating on the headlight lens in a circular or back and forth direction. 6. Within 5 minutes, inspect the headlight with adequate lighting looking for any thick areas that have not flashed away to clear. 7. Use the foam applicator or an Optimum Multi-Surface Microfiber Towel to wipe down and remove any excess.